Category » Crystal Report Writer
Crystal Report Writer
There were 11 questions found in this category:
"Failed to open rowset" when viewing Crystal Report in Sage MAS 90 or MAS 200
The error message "Failed to open rowset" may display when attempting to open a report or form in Sage MAS 90 or MAS 200.To diagnose the error:1. Try opening or running the report from a full version of Crystal Reports as this may give a more complete error message.2. If you're upgrading from an ...- Error 88, Line 1170 running custom Crystal off MAS 90 menu
When trying to run a Crystal Report off the Custom Menu within MAS90 or MAS200 an Error 88 - Line 1170 may result.One reason this may occur is if you have a Crystal Report with several sub-reports but the main report itself doesn't have a data table.Add a data table to the MAIN report and this e ...
- Guide to modifying Crystal forms
The attached guide explains how to use Crystal Reports to modify existing MAS90 forms. While the guide was written for v3.7x - the concepts are equally applied to most modules.
- How do I install Crystal Reports
When installing Crystal Reports, first be sure that you have the correct version of Crystal for MAS90 by reviewing the attached PDF titled Integrated Solutions Matrix March 7 2007.Refer to the attached Crystal Installation guide for step by step instructions.In general Crystal Reports is instal ...
- How do I print multiple copies of a label or report from within Crystal
I am trying to print labels, and would like the record to "repeat" based upon a fixed quantity. EG, I have item number 12000xyz and I have quantity ordered 20 pieces. Is there a way to have the Item number repeat 20 times?Other than manually controlling the # of copies for each label via printe ...
- mascrcw utilitiy continues to prompt for user code and password when converting crystal reports
Applies to: All versionsIf you use the MASCRCW utility to convert Crystal Report files, you may continously be prompted to log into the Sage MAS 90 or 200 database.The solution is to setup the ODBC driver with your Sage MAS 90 or 200 user name and password.This can be done during the initial log ...
- Sage MAS 90 and MAS 200: Error 12 SWCOCX 130, "A DLL is either corrupt, not been properly registered, or incorrect version...", when printing graphical forms or Crystal reports
Prior to Sage MAS 90 and 200 3.71, Error 65 SWCOCX 8460 normally occurred under the circumstances listed below. MASCR.DLL is missing from ..\Mas90\Home. Sage MAS 90 or 200 may have be upgraded from version 3.51 or prior versions, but Workstation Setup has not been run on the workstation.Run Work ...
- Sage MAS 90 or 200: Unable to open the specified report. (err/ret=22/0) occurred on line 170 in program SWCOCX"
The error message Unable to open the specified report. (err/ret=22/0) occurred on line 170 in program SWCOCX" may occur when attempting to print a Crystal Report or form.This usually indicates:a - The workstation has the wrong version of Crystal Reports installed. Check the compatibility guide o ...
- Very slow Crystal Report printing
In some instances your Sage MAS 90 software may run at normal speeds while your Crystal based forms and reports print exceptionally slowly.There can be many causes, here are a few of them:A - Make sure you have your anti-virus set to exclude files with RPT file extensions. Exclude these from sca ...
- Where can the Crystal Reports knowledgebase now be found?
Crystal Reports was purchased by SAP. The new knowledgebase for Crystal Report Writer can be found at the following link:https://www.sdn.sap.com/irj/sdn/businessobjects-supportDown towards the bottom of the page you will see sections called Notes, Articles and Downloads. Notes is the Knowledge ...
- Windows update causes error message when printing report
During a recent Windows upgrade, some of the printers on the network appear to have been renamed.One printer was named Extended Solutions PDF Converter and after the Windows Update installed, the printer displayed with a new name Auto Extended Solutions PDF Converter.Error messages stopped, once ...